OEM Style RGB Clear Taillights for Infiniti G37 Coupe | 2008-2013 G37 Coupe & 2014-2015 Q60 Coupe | Plug & Play | App + Remote RGB | Sequential Turn | Unleash the Ultimate Look
Unleash the ultimate look on your 2008-2013 Infiniti G37 Coupe or 2014-2015 Q60 Coupe with these OEM Style RGB Clear Taillights that keep the clean factory housing shape you love but swap the stock red lens for a crystal clear outer with custom RGB LED boards inside, because your coupe deserves to stand out at meets without looking cheap or losing the OEM panel fitment, and these use the exact OEM Stanley dimensions so they bolt to your quarter panel and trunk with factory 8mm nuts and perfect panel gaps while the clear lens shows off the multi-layer LED setup that runs bright red for tail and brake by default to stay DOT legal, then switches to full RGB mode via Bluetooth app or RF remote for 16 million colors, breathing, strobe, chase, and music-sync effects, plus built-in sequential amber turn signals and instant-on white reverse, and every set is sealed to IP67 and potted so rain, car washes, and trunk condensation won’t kill the boards, and wiring is 100% plug & play to your stock harness with built-in resistors and CANBUS so there’s no hyperflash, errors, or coding needed on any G37 Coupe trim including Base, Journey, Sport, IPL, or AWD as well as the 2014-2015 Q60 Coupe, and the lenses are UV and hard-coated polycarbonate to resist hazing, yellowing, and rock chips while the red LED intensity meets DOT brightness for street use, and the RGB elements shut off when you’re in normal drive mode so you can daily it clean then go full show mode at night, and every pair is bench-tested for LED function, sequential timing, color accuracy, and seal integrity, making these the easiest way to get a custom, modern rear end on your G37/Q60 Coupe with OEM fit and RGB versatility that gets attention everywhere.
Key Features:
- Fits 2008-2013 G37 Coupe & 2014-2015 Q60: Direct bolt-on for Base, Journey, Sport, IPL, and AWD Coupe. Matches OEM Stanley housing dimensions.
- OEM Style Housing with Clear Lens: Keeps factory shape and panel gaps. Crystal clear outer lens shows off custom LED internals vs stock red.
- 16 Million RGB Color Options: Bluetooth app + RF remote control. Set any color, plus breathing, strobe, chase, and music-sync modes for show use.
- DOT-Legal Red Tail & Brake: Defaults to bright red for tail and brake lights. Meets DOT brightness for daily street use and inspections.
- Sequential Amber Turn Signals: Modern sweeping amber motion for turns. Clean, high-visibility signaling that’s hard to miss.
- Instant-On White Reverse LEDs: High-output white LEDs for reverse. Better visibility than dim OEM 7443 bulbs.
- Plug & Play to Factory Harness: Uses stock connectors with built-in resistors and CANBUS. No errors, hyperflash, or wire splicing.
- IP67 Waterproof & Potted Boards: Fully sealed housing and potted electronics. Safe in rain, snow, car washes, and trunk condensation.
- New OEM-Style Foam Gaskets Included: Fresh body gaskets seal against quarter panel and trunk. Stops water leaks and wind noise.
- UV & Hard-Coated Clear Lens: Polycarbonate resists hazing, yellowing, and rock chips. Stays crystal clear for years.
- App-Controlled Show Mode: Switch between street mode and full RGB with your phone. Colors auto-shutoff in drive for legal daily use.
- Perfect Panel Gap Fitment: Injection-molded to match coupe body lines. Flush fit with proper trunk clearance and factory seal compression.
- High-Density 5050 RGB SMD LEDs: Even illumination with no hot spots or dead zones. Bright enough for day and night visibility.
- 30-Minute Bolt-On Install: Access through trunk trim. Remove factory nuts, unplug, and swap. Basic hand tools only.
- Bench-Tested Before Shipping: Every pair checked for LED function, sequential timing, color accuracy, remote pairing, and seal integrity.